Hellow guys, Welcome to my website, and you are watching How to Install Platinum Complete Toilet Repair Kit - 4010MP | Korky Toilet Repair. and this vIdeo is uploaded by Korky Toilet Repair at 2022-01-07T13:35:22-08:00. We are pramote this video only for entertainment and educational perpose only. So, I hop you like our website.
| Name | How to Install Platinum Complete Toilet Repair Kit - 4010MP | Korky Toilet Repair |
| Video Uploader | Video From Korky Toilet Repair |
| Upload Date | This Video Uploaded At 07-01-2022 21:35:22 |
| Video Discription | QuietFILL® Platinum® Complete Toilet Repair Kit (4010MP) https://www.korky.com/parts/kits/quietfill-platinum-universal-toilet-repair-kit Hello and welcome to Korky Toilet Repair! Today we are going to install your new Korky Platinum Complete Toilet Repair Kit. The first step is to shut off the water supply to your toilet. Next, flush your toilet. Mark the water level in the tank with a pencil. Hold the handle down to drain the excess water. Sponge out the remaining water in your toilet tank. Place a bucket underneath your tank to catch any excess water. Disconnect the water supply line and remove the mounting nut. Remove the old fill valve. Locate and remove all old nuts, bolts & washers from the tank. Carefully lift up on the tank and remove it from the bowl. Note: The new gasket may look different than your old one, but it will replace virtually all shapes and thicknesses. Remove the old gasket. Remove the old mounting nut and pull the old flush valve & flapper out of the tank. Place your new Korky flush valve into the tank and slide the chipboard washer over the threads. Hand-tighten the mounting nut. Place the new gasket over the mounting nut threads. Carefully set the tank onto the bowl. The new gasket may be thicker than your old one, causing the tank to sit higher and wobble. This is normal - the gasket is designed to compress. Use the new bolts, rubber washers, washers and hex nuts in the packaging to attach the tank to the bowl. It may be helpful to have a second person apply downward pressure to keep the tank level as you tighten the nuts in an alternating fashion. Tighten until the tank stops wobbling or until the tank and bowl touch, whichever comes first. Do not overtighten, doing so may cause the porcelain to crack. Next, set the height of the flush valve. Loosen the locknut and extend the overflow tube until the top of the overflow tube is 1" below the flush lever nut. Then hand-tighten the locknut. Turn the top of your new fill valve counterclockwise and pull up to fully extend. Place the valve in the tank and push down until the corner of the silver cover lines up with the top of the flush valve. Lock the fill valve in place by twisting the upper half clockwise. Make sure the rib on the top of the fill valve lines up with the pegs on the bottom half. Place the locked valve in the tank, screw on the mounting nut, insert the metal clip into the refill tube and attach the clip to the flush valve. Make sure the refill tube has a direct path to the fill valve. Trim the tube if needed and then attach to the fill valve. And reattach the water supply line. Turn the refill adjuster clockwise to the fully open position. Attach the flapper chain to the flush lever with minimal slack. Turn the water supply on and wait for the tank to fill completely. Turn the water supply off and flush. If the water drops within 1/2" of the pencil mark, your flapper installation is finished. If not, rotate the band to the open position and reinstall the flapper. Turn the water supply on and let the tank refill completely. Turn the water supply off and flush. If your water level is still not within 1/2" of the pencil mark, adjust the dial so that the next lowest number aligns with the arrow. Then, reinstall your flapper. Turn the water supply on and let the tank refill completely. Turn the water supply off and flush. Repeat this process until the water level drops within 1/2" of the pencil mark. Turn the water supply on and let the tank refill completely and flush. Wait 2 minutes for the water in the bowl to settle, the excess water will drain out. Mark the water level in the bowl with a pencil or dry erase marker. Flush. If the bowl water level reaches the mark before the tank is finished filling, turn the dial counterclockwise to reduce flow. If the bowl water level is below the mark once the tank is finished filling, turn the dial clockwise to increase flow. Repeat this process until the water level reaches the mark at the same time the tank is finished filling. Congratulations - you have successfully installed your new Korky Platinum Complete Toilet Repair Kit! |
| Category | Howto & Style |
| Tags | Howto & Style Download MP4 | Howto & Style Download MP3 | Howto & Style Download MP4 360p | Howto & Style Download MP4 480p | Howto & Style Download MP4 720p | Howto & Style Download MP4 1080p |
